Product Name:AK027*1 TB421*1 220v 433m RF Wireless AC Motor Reverse Controler Start Stop SwitchPacking list:
1 PCS 2 Channel 433M 220V receiver contrller;
1 PCS 3 button 433M Remote Controler(Use 12V 23A batteries ,NOTE : Batteries not included);
Receiver :
Technical indicators:
Working voltage: AC220V;
Operating frequency: 433.92MHz;
Receiver sensitivity:-95dB;Encoding: Receiver Recording;Momentary / Latch / Toggle selectable (defult is Momentary , Latch Mode need 2 buttons handsender );Output mode : Relay switch or AC220V power switch (Relay switch is defult ) ;Receiver size: 62 * 35 * 22 mm;
Max load : 500W;
2 Channel;
Advantage :
1: Receiver Mother board have a learning key , if the remote is lost , must buy EV1527 or PT2262 remotes to re-learn;
Work mode (programmable )
singnal Inter-locking (Latch)singnal Self-locking (Toggle)singnal Non-locking (Momentary is defult )
Momentary------------Press the Transmitter button A, the receiver relay A is ON, release button A; the receiver relay A is OFF, the same as B/C/D ,Every channel is Independent ;
Toggle---------------Press transmitter button A for 1 time , the receiver relay A is ON, press button A again, the receiver relay A is OFF, the same as B/C/D. Every channel is Independent ;
Latched------------------
Press transmitter button A, the receiver relay A is ON, the relay B/C/D is OFF.
Press transmitter button B, the receiver relay B is ON, the relay A/C/D is OFF.
Press transmitter button C, the receiver relay C is ON, the relay A/B/D is OFF
Press transmitter button D, the receiver relay D is ON, the relay A/B/C is OFF.
User guide instruction :
1:Clear the deposit information
Keep pressing learnig key on receiver controller board , LED turn on after 2 seconds , then turn off after 4 seconds , it means clearing successfully . ( our remote is already programmed before dispatch , please don't clearing ).
2: Relay working mode selecting :
1: keep pressing learning key on the receiver controller ,
LED turn on after 2 second , then turn off after 4 second, then the receiver controller enter programming state , but not release the finger , still keep pressing the learning button , LED blink once after 2 second , release the finger on learing key , it is Momentary mode ,
or still keep pressing learing key ,
LED blink twice after 2 second , release the finger on learing key , it is Toggle mode ,or still keep pressing learing key ,
LED blink 3 times after 2 second , release the finger on learing key , it is Latch mode ,
3: Learning the remote to the receiver controller:
A: Keep pressing learnig key on receiver controller board , LED turn on after 2 seconds , release the finger on learning key , press '' A'' buttons on the remote work state LED blink 3 times , it means ''A'' buttons was memoried by Channel 1 .
B: repeat step A to memoried ''B'' button by Channel 2 .
light connection :
motor connection :
Transmitter Remote:
Qty : 1 pcs 3Button Fixed code remote ;
Features / Specifications :
1. 3 buttons;
2. High stability, SMT chip, frequency stabilization SAW, ultra-high-frequency transistor;
3: Large power;
Transmitter Module No.: TB421;
Power supply : 12V 23A battery (not included )
Operating current: 28-33mA;
Oscillation mode: SAW resonator;
Modulation mode:ASK/OOK;
Operating frequency:433.92MHZ ;
Encoding format: SCT2260 fixed code (compatiable for PT2262 SC2262 PT2260 PT2264 , can work with PT2272-M4 ,PT2272-T4,PT2272-L4 );
RC Resistance : 4.7M;
Transmit power : 200mW ;
